DM8806: 6-Port Ethernet Single Chip Switch Controller with GMII/MII/RMII
Features
• Ethernet Switch with five 10/100Mb PHY, five 10/100Mb MAC and one MII/RevMII
• compatible to IEEE802.3u and IEEE802.3az
• Temperature Range: 0°C to 70°C and -40° to 85°C
• Fiber mode FEF (Far End Fault)
• 50MHz clock out for RMII Interface
• Cut-thru function and Store-and-forward
• Per port supports 4 priority queues , Port-based, 802.1P VLAN, MAC based, IPv4 TOS
• Supports 802.1Q/port-based VLAN up-to 16 VLAN group with full 12-bit VID: tag/untag
• Per port support bandwidth, ingress and egress rate control
• Supports Broadcast Storming filter function
• Supports Back Pressure Flow Control in Half-duplex mode.
• Recodes up-to 2K Uni/Multi-cast MAC addresses
• Automatic aging scheme
• Support MIB counter
• Support multicast filter function
• Register access by MDC/MDIO format
• Support trunk ports
Block Diagam DM8806
The DM8806 is a fully integrated Fast Ethernet Switch controller for normal and extended temperature range with five 10/100Mb PHY, five 10/100Mb MAC plus one 10/100/1000Mb MAC, and an MII/GMII interface option for a 6th MAC.
The controller offers basic Layer 2 switch features and advanced IEEE 802.1Q VLAN, priority queuing, IEEE 802.3az Energy Efficient Ethernet, IGMP snooping and Spanning Tree protocol.
All ports support FX, only ports 0 and 1 support LFP/FEF. Fiber mode requires an external EEPROM. Only PTPv1 boundary clock is supported.
The integrated PHYs are compliant with the IEEE 802.3u standards. The MII/GMII interface offers the possibility for flexible connection of 10/100/1000Mb PHYs.
In mode 2A (different pin assignment to mode 3) the GMAC and the GMII interface can be used. Details can be found in the separate data sheet for Mode 2A and the introduction to the DM8806.
The standard EVB of the DM8806 is configured to Mode 3.
General
01 Davicom General Layout Guide | 718.85 KB | |
02 Davicom Hardware Layout Guide | 9.4 MB | |
03 DACOM Ethernet Design-In Guide | 2.64 MB | |
04 Connecting two MII devices without transformers | 76.04 KB | |
05 Design hint Center-Tabs Transformer to PHY | 305.47 KB | |
06 Crystal Information | 58.87 KB | |
07 Programming Reference Flow-Chart | 130.04 KB |
Part-Specific
11 DM8xxx Crossed RMII | 91.26 KB | |
12 DM8xxx Reduced MII | 46.54 KB | |
13 DM8xxx Reverse MI | 89.93 KB | |
14 DM8xxx Reverse RMII | 70.76 KB | |
15 DM8806 introduction and application | 90.73 KB | |
16 DM8806 EVB Schematic Mode 3 | 111.77 KB | |
17 DM8806 Schematic Demo Board Mode 2A Gigabit MAC | 222.65 KB | |
18 DM8xxx Programming Guide | 163.22 KB | |
19 DM8806 Reliabilty Test Report | 112.34 KB | |
20 DM8806 Cut-Through Configuration and Use | 167.85 KB | |
21 DM8806 10-port GPHY M2A | 164.63 KB | |
22 DM8806 Demo Board Jumpers Definitions | 37.5 KB |